Clik here to view.
Nerf Hammershot 8 Shot Cylinder
This is my version of an 8 shot Hammershot Cylinder (yes, eight shot) This has not been tested, so it may not work as well as intended. This is also a remix of the following design (which is a...
View ArticleClik here to view.
video conferencing robotic nerf gun turret
Used these Slotted Aluminum Extrusions from adafruit. Also, these corner braces. This is an open source project, and we hope you'll contribute. Either by improving our 3D models. Or by contributing...
View ArticleClik here to view.
Nerf 2.5" Picatinny Rail Adapter
2.5" rail adapter for tactical accessories. Includes a nub to lock into existing Nerf rail locks. Tested to fit on Nerf rails, but have not tested actual Picatinny attachments. However dimensions were...
View ArticleClik here to view.
Nerf Firestrike Removable Iron Sights
Basic removable front and rear iron sights. Parts simply slide on and are held by friction. Front sight may be glued in if desired, but back should be removable to allow the blaster to be opened....
View ArticleNerf Retaliator Pump Grip
Based off of the design by dyson72 Go to his thing here http://www.thingiverse.com/thing:1626947 for instructions to install.
View ArticleClik here to view.
Buzz Bee doubleshot / Rick's Shotgun shell
A 3d model I made of the shells that are required for use in the Buzz Bee Double shot and Rick's Shotgun blasters.
View ArticleClik here to view.
Nerf Bio Harzard Site-Remix
This is a remix of the Nerf Biohazard Sight. I tried printing the original one but the Biohazard part was did not attach to the outer ring at least when I printed it. Also the mount for the sight was...
View ArticleNerf Iphone 5c Case holder
I did not see an iPhone 5c case phone holder for nerf gun attachments, so I decided to create something for you guys.
View ArticleFoam Dart Warhead (fixed)
The original file seems to have an error, as it printed with the front closed. Loading the file into 3D builder fixed the problem.
View ArticleClik here to view.
Nerf Lawbringer Wall Rack
Hang your nerf gun on the wall. Onshape Design Made by MatterHackers.
View ArticleClik here to view.
Base plate for jumping target
This is another base plate for the jumping target. It adds a little more weight and stability. It also has screw holes for fixing it to a wooden board.
View ArticleClik here to view.
Custom Nerf Sniper Scope (TF2 Inspired)
A custom scope attachment that will attach on to any Nerf blaster with a Tac-rail on it. The exterior design was loosely based on the scope of the sniper rifle used by "The Sniper" in Team Fortress 2....
View ArticleNerf Longshot Catch Model
Direct replacement catch model. I would not recommend printing it using standard extrusion printers , as it will always be weaker than the original injected catch. I'm just putting the model out here...
View ArticleClik here to view.
Nerf Longshot Flared Magwell Rev. 2
Flared magwell for the Nerf Longshot. This adds roughly 1 inch widthwise and half an inch lengthwise, aiding in reloads. Single part is friction fit on, while left and right halves are designed to be...
View ArticleClik here to view.
FDL-2 Blaster
The FDL-2 is the successor to the FDL-1 Robotic Foam Dart Lancher. It is similar in function but instead of "Mega" sized darts firing from a revolver, it is designed to accept Nerf brand magazines and...
View ArticleClik here to view.
Nerf N-Strike Elite Triad Ex-3 Holder
Makes the perfect companion for your Nerf N-Strike Elite Triad Ex-3. Saves space. Looks cool. Holds six rounds, perfect for 3 suction cup and 3 "hard tip" nerf darts. More of my designs can be found...
View ArticleClik here to view.
Jolt Dart Holder and Tactical Rail
This is designed to clip a Nerf Jolt to a Nerf Tactical Rail. It also holds extra darts. This clip is a redesign of Swift2568's Ammo Clip (http://www.thingiverse.com/thing:1479330). I liked his design...
View ArticleClik here to view.
Nerf Stryfe Parametric Battery Door
I cleaned up DFrostedWang's battery door model and made it adjustable to different widths. Just open the Fusion 360 file and change the Height parameter to whatever you want. The numbers are the height...
View ArticleNerf Recon Piston
The piston for my Nerf recon recently broke, so I took some measurements and created this in blender. It's at 1/10th scale, so it must be scaled up before being printed. I haven't printed it yet, so I...
View ArticleClik here to view.
DoubleU-Foam-Dart-Launcher (DUFDL)
Inspired by the original NERF elite guns commercialy available, I made my own, compatible with the original (and chineese) NERF clips (or drum) Currently writing the firmware for an ESP8266, but...
View Article