Gryphon - Shorter Rev Trigger
A friend asked for a shorter Rev trigger, so I edited the file to make it shorter. Just in case someone else wanted the file, here it it.
View ArticleClik here to view.
"stargate" loading adaptor for Nerf Perses
This is simply an adaptor to mount the Mechanical Iris by JDMc to the nerf Perses hopper by Memoir. As the size of the hopper opening is sized for paintball lids, this may work on many other hoppers...
View ArticleThe Dead DP
This is a semi only gun called the Dead DP. Please do not make it into a real gun. If you want to make it airsoft or nerf. If you finish it and make it please send it to me. I would like to see this...
View ArticleClik here to view.
TalonClaw - Ram Rod with Carbon Fiber Rod
3d Printed Ram Rod for TalonClaw with a Carbon Fiber insert for strength. Note: the tolerance is tight to fit the rod inside (was printed on a Prusa i3 MK3) The model in the photo is a proto-type I...
View ArticleClik here to view.
Sliding Clutch Operated Barrel Attachment Clamp
Or SCOBAC for short. It's a barrel clamp with no nuts, no screws, no tools, fast, fully accessible without having to pullback the priming pump, and 100% fully printable. It translates the tension...
View Articlenerf rail 3x hcog ranger (Apex Legends)
This the 3x hcog ranger from Apex Legends, it easily slides onto the rail of any Nerf gun.
View ArticleStryfe W Front Piece
Remix to front Stryfe piece to fill in sling point but also flattened the front end, keeping ability to accomodate NStrike accessories. Shortened wings and simplified other decorations to speed print...
View ArticleClik here to view.
Nerf Takedown XX-800 Blunderbuss Muzzle
This is a blunderbuss muzzle attachment for the Nerf Rival Takedown XX-800. The attachment fits securely into the barrel, but the locking ring may need to be adjusted with some light sanding depending...
View ArticleClik here to view.
Sledgefire Flare strip
I borrowed Cramplehade's measurements (also didn't wanna recreate the sledgefire shell shape when it was available.) and since blender's a bit iffy on scaling. i don't wanna bother with scaling. Print...
View ArticleClik here to view.
SledgeThunder Barrel v2
V2 is finally out I added a gasket o-ring for better seal and made the barrel diameter the same diameter as the inside of the shell to where the rival rounds have a better seal as well the shells also...
View ArticleClik here to view.
Worker Hurricane grip extension
A grip extension for the Worker Hurricane blaster to provide more room for larger batteries. Simple snap-fit. Prints without support.
View ArticleClik here to view.
sledgthunder cylinder bore-v2
this is a revision of the version 2 of my barrel allowing you to fire any shell from the spring thunder series including with the double elite Nerf shot and the 3 shot pleshette boomco darts V2 is...
View ArticleClik here to view.
Underbarrel Bigshock for Alpha Trooper
Something I made for HvZ that attaches a bigshock to an alpha trooper to give it a foregrip and mega dart firing capabilities similar to a stryfle. I designed it to use the screws from the alpha...
View ArticleClik here to view.
TalonClaw - Ram Rod with Carbon Fiber Rod MKII
I modified my original design to make it easy to release the mag from the mag-well in the forward position. I also sanded the carbon fiber rod a bit to make the surface rough for were I glued the...
View ArticleClik here to view.
Nerf Worker KO baseplate
mag plate created for: https://www.amazon.com/Worker-12-Dart-Reload-N-Strike-Blaster/dp/B01C5ZJ7Q0 the 12 round worker mag.
View ArticleClik here to view.
ShellStrike DS-6 Spring Spacer and Reinforcements
Spring Spacer for the Nerf ShellStrike DS-6 Blaster prints in two halves so you can install them into the plunger head without removing the plunger rod. (see photo, yellow spacer) In theory, there is...
View ArticleJSS Scar (Need 29mm of 9/16 inch K&S Brass)
My design on a rifled barrel for Nerf blasters. This is a 1/4 twist over 50mm. There are 4 rifling lines. One end is meant to fit on a 16mm barrel. The other end is to fit a 29mm long 9/16 inch K&S...
View ArticleClik here to view.
Caliburn Elite Magazine
The bottom attachment points were preventing me from fully loading the original. They kept hitting the handguard. This remix repositions them to the side and gives a little extra flair to the bottom to...
View ArticleClik here to view.
Nerf Double Magazine
Be sure to print out the 'Mag' and 'Spring' files twice. I loved the original design with the spring. I wanted to have a double-sided version for twice the capacity and tacti-coolness. Basically all I...
View ArticleOFP Morpheus Rayven Cage 41.5mm
This is a modified version of OFP's Morpheus rayven cage, modified to fit the nerf rayven blaster. I own nothing.
View Article